Tractor Failure Analysis
Nov 07, 2023
1. The oil supply switch of the fuel tank leaks oil: the reason is that the graphite and asbestos oil seals at the switch are damaged.
Exclude:
(1) Remove the switch, take out the packing, use oil-resistant rubber sheets to make two round pads with an outer diameter 1 mm larger than the switch housing hole and an inner diameter 1.50 mm larger than the handle screw, sandwich the rubber pads between the steel pads, and then Put them on the handle screw together and tighten the gland device.
(2) Wrap graphite and asbestos rope between the two steel pads and fill them up, and tighten the gland device.
2. The oil tank drain faucet leaks oil: the reason is that the steel ball in the faucet is rusted or failed.
Troubleshooting: Replace the steel ball (the diameter is 15 mm, and the steel ball in the bearing with an inner diameter of 80 mm can be used instead).
3. Oil leakage from the bell mouth of the oil pipe: The reason is that the cone surface of the oil pipe bell mouth and the bell mouth seat are not properly sealed.
Exclude:
(1) Tighten the end of the connector with the horn first.
(2) After grinding the bell mouth joint, apply sealant on the cone surface, then tighten or saw off the bell mouth, and re-expand it with an expander.
4. Oil leakage from hollow screw joints: the reason is
(1) The end face and gasket of the oil pipe joint are uneven;
(2) The screw holes on the shell are uneven.
The troubleshooting method is as follows: smooth the joints and washers. Flatten the hexagonal inner surface of the cannulated screw, and then tighten it or apply sealant on both sides of the gasket.
5. Oil leakage at the joint surfaces of the casing: The reason is oil leakage at the joint surfaces of the oil pan, cylinder head, valve cover, timing gear chamber cover, gearbox cover, starter gearbox cover and other casings, usually due to The fasteners are not tightened, and the gasket is damaged or failed.
Exclude:
(1) Do fastening work regularly.
(2) For parts that are not frequently disassembled, such as paper pads, red glue can be applied to both sides of the paper pads;
(3) For joint surfaces of frequently disassembled parts such as valve chamber covers, filter housings, etc., asbestos pads should be used and lead oil should be applied to the pads. When tightening, the bolts at the location should be tightened symmetrically several times. In addition, it should be ensured that the gasket is intact, the joint surface of the parts is flat and clean, and there is no misalignment or deformation of the parts.
6. Oil leakage at each joystick shaft: the reason is
(1) The sealing gasket is damaged.
(2) The matching gap between the shaft and the hole increases.
Troubleshooting: A suitable oil-resistant rubber can be used as a gasket according to the diameter of the rod shaft. Its inner diameter is 1-3 mm smaller than the shaft diameter. It can be installed on the shaft surface in contact with the hole wall and pressed tightly.
7. Oil leakage from the crankcase: The reason is that the paper pad is damaged or the screws are loose.
Troubleshooting: Remove the oil pan, remove the gasket and check. If the gasket is intact, wipe it clean and apply a layer of red glue; if it is damaged, replace it with a new gasket. Apply a layer of red glue. Screws should be tightened symmetrically and evenly.
8. Oil leakage from high-pressure oil pipes: The reason is that after long-term use of high-pressure oil pipes, the cone surface of the joint has been worn, resulting in loose sealing.
Troubleshooting: Place a piece of plastic pipe 1-2 mm long and about 5 mm in diameter at the joint between the cone surface and the cone hole of the high-pressure oil pipe, or place a copper washer with an inner diameter slightly larger than the inner diameter of the oil pipe and an appropriate outer diameter, or replace it with a new high-pressure oil pipe. .
9. The gearbox leaks gear oil: the reason is
(1) The matching clearance between the gearbox bearing and the shaft hole is too large;
(2) Oil seal wear and aging.
The troubleshooting method is as follows: The gap in the shaft hole of the box body is too large, which can be repaired by the inserting method. If oil leakage occurs due to wear and aging of the oil seal, the oil seal should be replaced.
10. Oil leakage from supporting rollers, supporting pulleys and guide wheels: the reason is
(1) The rubber sealing sleeve is worn and aged;
(2) The sealing ring is severely worn.
The troubleshooting method is as follows: replace the rubber sealing sleeve in time. Replace the large upper sealing ring. The two rough joint surfaces of the sealing ring must be properly ground and a layer of graphite grease should be applied on both sides. After installation, water and dirt must not be allowed to enter for 24 hours.
11. Oil leakage from oil filling port and oil drain port: the reason is
(1) The threads and pitches of seals in diesel tanks, gasoline tanks, hydraulic tanks, diesel coarse and fine filters, high-pressure oil pumps, oil pans, gearboxes, etc. are inconsistent.
(2) The diesel tank cover has no sealing rubber.
The troubleshooting method is as follows: Keep the screws and thread pitch of the seal consistent, and use all fine buckles. Install sealant rubber.






